Standards M12 connectors are the IEC 61076-2-101:2012 standard. The original IEC standard was published in 2003 and is currently in its third revision. In 2021, a new push-pull M12 standard, known as IEC 61076-2-010;2021, was released.
Table of Contents
Are all M12 connectors interchangeable?
M12 connectors are one of the most popular industrial connector solutions on the market. They are part of an IEC specification that ensures all A-Code connectors are interchangeable with each other.
What is the diameter of a M12 connector?
The M12 name originates from how the metric thread on most of the connectors’ coupling nuts and mating receptacles (described in more detail shortly) are essentially 12-mm-diameter fasteners with an M12 thread.
What is an A coded M12 connector?
The M12 A-Code product line from Stewart Connector are standard products used in industrial automation, outdoor applications, measurement and control, agriculture and more. A-code M12 connectors are often used for sensors and DC power.
What is the difference between an M8 and M12 connector?
M8 connectors have M8 size mating thread, M12 connectors have M12 size mating thread, and so on. Another difference is the pin counts. M8 connectors have 3, 4, or 6 pins, M12 connectors have 2-12 pins, and M23 connectors have 6-19 pins (although the most common are 12 or 19 pins).
Are M12 connectors waterproof?
The M12 connecting interface features waterproof protection (IP65/IP68/IP69K), cross-manufacturer compatibility (IEC 61076-2), and multipurpose applications (Signal, Power, Network). The standard codings of M12 are A-, B-, D-, K-, L-, X-, S-, and Y coding.
What is a coded connector?
A-coded connectors are the most common style of connector. These are used for sensors, actuators, motors, and most other standard devices. A-coded connectors can vary in its number of pins, anywhere between two pins and 12 pins. B-coded connectors are mostly used in network cables for fieldbus connections.
What size is an M8 connector?
The M8 connectors can be soldered to cables with #24AWG conductors, and a 4 to 6 mm (. 16 to . 24″) cable diameter. Male and female connectors, with straight or right angled connection styles provide a wide selection of connection options.
What is an M20 connector?
M20 Waterproof Cable Gland M20 cable gland connectors are widely used in all types of electrical instruments and automation systems, they used as sealing and termination devices the cable characteristics can be maintained for a long time.
How do you read gland size?
Cable gland size is equal to the size of the cable bundle diameter. For example, if your cable bundle diameter is 50mm means then you should select the 50MM cable gland only.
What is 2.54 mm pitch?
Dupont 2.54 mm Pitch connector is a low profile connector delivering 3.0A current for WG #22 to #28, available in 1 to 40 2*1 to 2*40 positions suitable for either power transmission systems or chassis wiring. Scondar offers a crimp style lock and a configuration which prevents users from inverted insertion.
Is M12 the same as 12mm?
Yes. M12 is a 12mm diameter thread. You have to be sure the thread pitch measured in threads per millimeter (1.5 here) is the same as what u need.
How do I know if my nut is metric or standard?
Metric fasteners are measured by length and pitch, or the distance between threads. So the systems are opposite in a way: The higher the TPI in a standard bolt, the finer the threads because there’s more squeezed into a set space. The greater the pitch on metric fasteners, the more distance between threads.
How are M bolts measured?
Do not measure the head of the bolt, measure the threaded part, outside of the threads. If your bolt is metric, then the diameter is stated using the letter “M”. For example, if your bolt has a diameter of 4mm then it is called an ‘M4 bolt’ if your bolt is imperial then it will be measured in inches.
Is 1363 a standard?
IS 1363 was originally published in 1960 and first revised in 1967. Subsequent to the publication of 1967 edition, many changes had been agreed upon at international level which have been reflec~ed in IS 1367 series of standards covering ‘Technical supply conditions for threaded steel fasteners’.
What size drill bit do I need for an M12 bolt?
M12 needs a 13mm bit, the bolt should push through and be snug, only use cup head bolts and hit them with a hammer to lock the square bit of the bolt into the timber.
How do I know what size nut I need for a bolt?
To measure the diameter of screws and bolts, you measure the distance from the outer thread on one side to the outer thread on the other side. This is called the major diameter and will usually be the proper size of the bolt.
Does M10 mean 10mm?
Steel bolt with M10 metric thread. Metric threads are designated with a capital M plus an indication to their nominal outer diameter and their pitch: This bolt is M10 x 1.5 – which means the outside diameter is 10mm and the threads are 1.5mm apart (the most common thread pitch for M10).
Can I use plastic glands on Armoured cable?
Six types of brass cable glands are available: Indoor – a versatile design good for different types of cable, including armoured, plastic and rubber-sheathed. Outdoor – these can be used with both plastic or rubber sheathed and unsheathed cables.
How do you specify a cable gland?
- The diameter of the inner bedding.
- The diameter of the lead covering.
- The short circuit fault rating of the cable armour.
- The type and size of the armour braid.
What is a cable gland used for?
The main functions of the Cable Gland are to act as a sealing and terminating device to ensure the protection of electrical equipment and enclosures, including the provision of: Environmental protection – by sealing on the outer cable sheath, excluding dust and moisture from the electrical or instrument enclosure.
What is M12 in Imperial?
3/8″ M10. 7/16″-14. 7/16″-20. M12-1.75.
Can I use a metric sockets on standard bolts?
Can you use Metric sockets on SAE fasteners or SAE Sockets on Metric Fasteners? Yes, you can use some sockets on both metric and SAE sizes. However, you need to be careful, as most times they are not exactly the same, and you can strip a bolt by using an SAE socket on a metric bolt and vice versa.
Are metric and standard bolts interchangeable?
For standard bolts, head size is measured in inches or fractions of inches; however, metric bolt head sizes are measured in millimeters, which can cause confusion if engineers attempt to apply metric bolts to standard systems, and vice versa.
Whats the difference in standard and metric?
Standard tools use the imperial or SAE measuring system, commonly used in the USA. Metric tools rely on the metric measurement system. The difference is in the units, where standard tools will use inches, feet, miles, and yards. The metric system uses millimeters, centimeters, meters, and kilometers for expression.